maximum ratings and electrical characteristics for capacitive load, derate current by 20%. single phase, half wave, 60hz, resistive or inductive load. rating at 25 o c ambient temperature unless otherwise specified. notes : -55 to + 150 fep16at symbol v rrm v rms v dc if (av) i fsm v f i r trr c j t j , t stg 50 100 200 140 200 400 35 70 280 50 100 400 600 420 600 16.0 10.0 175 1.3 1.7 0.98 35 250 90 2.2 unit v v v v a a ua ua o c pf o cw ns 300 210 300 maximum recurrent peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified peak forward surge current, 8.3ms single maximum instantaneous forward voltage maximum dc reverse current @t j =25 o c typical junction capacitance (note 2) operating junction and storage current t c =100 o c half sine-wave superimposed on rated load (jedec method) @ 8.0 a at rated dc blocking voltage @t j =125 o c maximum reverse recovery time (note 1) typical thermal resistance (note 3) features low forward voltage drop fast switching for high efficiency and high current capability case: molded plastic to-220ab heatsink high surge current capability weight: 2.03 grams polarity:as marked on body method 208 mounting position: any terminals: solderable per mil-std-202 mechanical data low reverse leakage current r jc temperature range (1) reverse recovery test conditions i f = 0.5a, i r = 1.0a, irr = 0.25a. (2) measured at 1.0 mhz and applied reverse voltage of 4.0 volts dc. (3) thermal resistance junction to case. epoxy: ul 94v-0 rate flame retardant 150 to-220ab unit : inch (mm) "ta" common cathode suffix "t" common anode suffix "td" anode and cathode coexistence suffix ? fep16a thru fep16j pb free plating product fep16a thru fep16j 16.0 ampere fast efficient plastic half bridge rectifiers ? 2006 thinki semiconductor co.,ltd. http://www.thinkisemi.com/ page 1/2 application automotive environment|dc motor control plating power supply|ups|inverter car amplifier and sound device system etc.. .196(5.00) .054(1.39) .038(0.96) .419(10.66) .139(3.55) min .624(15.87) .269(6.85) .548(13.93) .50(12.7)min .177(4.5)max .226(5.75) .163(4.16) .045(1.15) .019(0.50) .025(0.65)max .1(2.54) .1(2.54) .387(9.85) pb positive ct negative ct doubler common cathode case case case common anode series connection suffix "t" suffix "ta" suffix "td" glass passivated chip junction FEP16ATA fep16atd fep16bt fep16bta fep16btd fep16dt fep16dta fep16dtd fep16ft fep16fta fep16ftd fep16gt fep16gta fep16gtd fep16jt fep16jta fep16jtd
fig.1 - forward current derating curve fig.3 - typical instantaneous forward characteristics average forward rectified current, amperes 16 8 6 4 10 13 iinstantaneous forward current, amperes 0.1 1.0 10 0.01 0.4 0.2 0.6 0.8 1.0 1.2 1.4 1.6 0 0 50 100 150 case temperature, o c instantaneous forward voltage, volts fig.2 - maximum non-repetitive peak forward surge current peak forward surge current, amperes number of cycles at 60hz 0 25 50 75 100 125 150 175 200 110100 fig.4 - typical reverse characteristics percent of rated peak reverse voltage,% instantaneous reverse current, microamperes 0.1 0 1 10 1000 100 20 40 60 80 100 fig.5 - typical junction capacitance reverse voltage, volts 0.1 10 junction capacitance, pf 1000 1.0 4.0 10 100 100 60 hz resistive or inductive load pulse width 8.3ms single half-sire-wave (jedec method) t j =25 o c pulse width=300us 1% duty cycle t j =125 o c t j =25 o c t j = 25 o c f = 1.0 mhz vsig = 50mvp-p ? 2006 thinki semiconductor co.,ltd. http://www.thinkisemi.com/ page 2/2 fep16a-fep16d fep16f-fep16g fep16j ? fep16a thru fep16j
|
